Skip to main content

Old wardrobe gets second life as a retro arcade machine

IKEA TRYSIL wardrobe saved from landfill and converted into a retro arcade games machine.

We were dismantling our son’s TRYSIL Wardrobe to remove it from his room. It had been good wardrobe but the backing had started to continuously fall away.

It had some slight damage during dismantling and would have become landfill apart from a last minute idea….

A retro arcade machine!

retro arcade machine ikea hack

It actually looks pretty retro, and it plays like a real arcade machine.

IKEA items used: 
ikea trysil wardrobe

Related: MICKE desk with a built in arcade set up

Other materials and tools: 

DIY home retro arcade machine 

1. CABINET

First, dismantle the wardrobe (if it is already assembled).

Separate the 2 tall side pieces (Important! Leave hanging rod brackets ON! 2 x shelf pieces, 2 x drawer fronts, and any assorted bolts and screws. Dowel rods can be removed – I didn’t use them)

Mark out the side pieces to make 2 cuts.

cutting guide

Side Panel cutting Guide

This allows the cabinet to lean back at a neat angle. Ensure you identify the top and bottom correctly and take care to use the nicely edged side to stand towards the front. Cut with circular saw if possible. I used a jigsaw so cut is quite rough.

Mark out and drill pilot holes through sides to attach shelves between the 2 side panels. Use the long IKEA hex bolts that came with the TRYSIL to secure the shelves.

retro arcade machine ikea hack
2. SHELF FOR CONTROLS

On mine the middle shelf for controls is fitted at 93cm high and slopes very slightly toward the front.

retro arcade machine ikea hack

Once it is standing up use additional screws to fit the drawer fronts at the top.

retro arcade machine ikea hack

These are actually a little wider than the shelves but I squeezed mine in without cutting. But if you are better with a saw than I am you may wish to cut these down slightly to fit.

I also fitted the rear one at an angle and only used 1 screw on each side so it can flip up to access the TV.

Check that everything is holding together nicely then use 4 L-brackets to reinforce the structure.

I added an extra 2 brackets to the middle shelf for extra sturdy controls.

retro arcade machine ikea hack

Now, if you left on the hanging rod holders and measured correctly I found that the TV sat at the perfect height to support the 30” TV we had, donated by my in-laws.

LCD panel

I then fitted 2 screws in each top corner to allow TV to rest at the perfect viewing angle.

LCD panel

And that’s all I did for the cabinet.

If you want there are many other pieces that could be used to enclose the back of the cabinet and under the TV as well. (Again – I didn’t cut too much as I only had a jig saw and it cut this stuff very rough!). 

3. ARCADE GAMES SETUP

There are many instructional on Youtube on how to build an arcade games machine with a Raspberry Pi computer and Retro Pie.

retro arcade machine ikea hack

But here are the basic steps to fitting the joysticks and buttons to the USB controller, then connecting those to your Raspberry Pi mini computer.

First, search for a button layout online or design your own on a piece of paper.

Use this as a guide to drill holes for joystick and large buttons (28mm drill bit worked for me. Also some smaller buttons were 18mm I think – check your button sizes as they may vary). I did all this with the cabinet assembled.

The buttons should just drop in and screw tight and the joystick requires placement and a couple of short screws underneath.

The joystick kit comes with cables to attach to the USB board. These can also be fixed with a small screw or two.

controls

Then, take care to wire both player 1 and player 2 buttons in the same order as this will make the joystick configuration in the Retro Pie interface much easier.

How long and how much did it cost?
  • Joystick Button Kit: $50
  • Raspberry Pi computer starter kit: $99
  • L Brackets and other hardware: $20

The cabinet build took me about 3-4 hours, but I was making it up as I went along. Fitting in the joysticks and buttons took me about 2 hours. Programming Raspberry Pi computer was easy to do with lots of online tutorials. That took about 1 hour.

What was the hardest part about this hack?

Fitting the cabinet parts together. You may need another person to assist holding pieces in place while assembling the cabinet.

What to pay special attention to?

Cutting the large pieces so that the rubber edging remains in-tact for front edges of cabinet, which makes a nicer finish.

Be careful fitting the shelves as they are not particularly thick. They definitely need support with L-brackets.

Looking back, would you have done it differently?

No, it actually turned out almost exactly as I envisaged. I am still working out how to finish the cabinet with some more trimming beneath TV and control panel.

~ by Andrew Gelao (Katoomba NSW, Australia)

The post Old wardrobe gets second life as a retro arcade machine appeared first on IKEA Hackers.

Comments

Post a Comment

Popular posts from this blog

SKÅDIS: 5 ways to make the IKEA pegboard even better

IKEA introduced its own pegboard system, SKÅDIS, two years ago and I’d say it’s one of the best systems IKEA launched in recent years. I love how super customisable it is, with a growing range of accessories that help keep things organized. It works everywhere, in your wardrobe to bathroom . Probably anywhere you have a flat surface to hang it up. Photo: IKEA.com SKÅDIS pegboard system See it on IKEA.com But no matter how perfect a system, you can trust IKEA hackers to improve on the SKÅDIS. And they’ve settle these 5 issues you may have faced with the handy IKEA pegboard. Read on for their fixes. 5 IKEA SKÅDIS issues and fixes #1 Expensive hooks? You’ll need quite a number of hooks and accessories to fill up the SKÅDIS pegboard, and Kenyer was shocked at how quickly they all added up. So he figured he could make his own hooks to save cost. Photo: Kenyer Over at Instructables , he shows us how to twist copper wires into the SKÅDIS hook shape. It works s...
Post a Comment
Read more

Hackers Help: How to remake cam lock holes?

I want to put a 78.5” wide PAX configuration in a 77” space for a kids room . My plan is to eliminate the drawer on the right unit, then cut the shelves and rails to be 1.5” narrower. My question is, how do people attach two laminated pressboard IKEA pieces after they’ve cut off the cam lock holes? Related: See more Hackers Help questions and answers . Are they using drills bits and/or tiny hole saws to remake the cam lock holes? Or screws drilled in from the outside with wood glue? The outside pieces won’t be visible in my completed setup so I could go either way. I’m curious what other people are doing, either I haven’t seen this detail in past hacks or I haven’t been paying attention. ~ by Jenny *** Hi Jenny The best and tidiest method is to use the cut-off portion as a template to reproduce the same cam lock holes in the correct positions. The right sized drill bits and a  Forstner bit should do the trick. A Forstner bit will drill a flat-bottomed hole (...
Post a Comment
Read more

6 Clever & Easy IKEA FLISAT Table hacks for more Fun & Play

The IKEA FLISAT children’s table is quite a smart little thing. See those white covers? It’s a secret compartment. Open them up and you’ll fit 2 TROFAST storage tubs snug under the top of the table. Your child can reach in and get his or her LEGO bricks -– and then — most importantly, sweep everything down into the bin to clean up. Or at least that’s what we all hope the kiddo does! It’s also perfect for sensory play. Instagram is full of ideas on what to add to those tubs to maximise them. Think of filling them with rice, pasta or chickpeas, you name it, to develop fine motor skills. Read on to see how you can make the $50 table work harder for so much more fun. #1 Simple mod turns the IKEA FLISAT into a Play & Craft table Lauren has a very simple yet practical hack to turn the FLISAT children’s table into a play table with more storage and better organisation. Materials: Photo: IKEA.com FLISAT table with TROFAST tubs ONSKLIG change table containers Wood bracket ...
Post a Comment
Read more